Furnace not heating? Here are the safe checks St. Louis homeowners can do first, and the signs it is time to call for furnace service.
The furnace was fine yesterday. This morning the house is cold, the thermostat says it should be heating, and nothing is happening. On a St. Louis winter morning, that gets your attention fast. Before you call, a few safe checks could save you a service visit, or at least help the technician find the problem sooner.

Safety First
Two situations are not for troubleshooting. If you smell gas, leave the house and call Spire’s gas emergency line at 800-887-4173 from outside. If a carbon monoxide alarm sounds, leave the house and call 911. Do not go back in to check the furnace in either case.
Six Checks You Can Make Safely
Work through these in order. None of them require tools or opening up the furnace.
1. The Thermostat
Confirm it is set to Heat, the temperature is set above the current room temperature, and the fan is on Auto. If the screen is blank or dim, replace the batteries. Check that a schedule or hold setting has not lowered the temperature on its own.
2. Power to the Furnace
Most furnaces have a power switch nearby that looks like an ordinary light switch. It gets bumped or turned off by mistake more often than you would expect. Then check the breaker panel. If the furnace breaker has tripped, reset it once. If it trips again, leave it off and call.
3. The Air Filter
A clogged filter restricts airflow, and a furnace that cannot move enough air may overheat and shut its burners off to protect itself. If the filter looks gray and matted, replace it and give the furnace a few minutes to try again.
4. The Furnace Door
Many furnaces have a safety switch that cuts power when the front panel is off or loose. If someone changed the filter recently, make sure the panel is fully seated.
5. Vents, Registers and Outdoor Pipes
Inside, make sure supply registers and return grilles are open and not covered by rugs or furniture. Outside, high-efficiency furnaces vent through plastic pipes on the side of the house. Leaves, snow, ice, or a nest in those pipes could keep the furnace from running.
6. The Gas Supply
Check whether other gas appliances are working. At the furnace, the handle on the gas valve should sit in line with the pipe, which means open. If you are not sure what you are looking at, leave the valve alone.
When to Call Instead of Checking Further
Some signs mean the problem is past what a homeowner should handle. Call for service if:
- The breaker trips more than once
- The furnace starts, runs briefly, and shuts off, over and over
- You see water pooling around the furnace
- You hear banging, grinding, or squealing
- A burning smell does not fade after the first few minutes of the season’s first run
- The furnace is running, but the air stays cold after you have checked the fan setting and filter
A furnace that locks itself out is usually doing its job. Resetting it repeatedly could work against a safety control that shut it down for a reason.
What to Have Ready When You Call
A few details help a technician arrive prepared:
- What the thermostat shows and what you have already checked
- The brand and rough age of the furnace
- Any blinking light on the furnace, and the pattern if you can count it (many furnaces flash an error code through a small window on the front panel)
- Any sounds or smells before it quit
Why It Helps to Call a Local Company
When the heat is out, you do not have time to sort through companies with local-sounding names that turn out to be part of national chains. A locally owned company answers to its neighbors. You should expect a clear explanation of what failed, your options, and a written quote before repair work begins. Thomas Hoffmann Air Conditioning & Heating repairs and replaces furnaces across the St. Louis area, including emergency heating service.

Get Your Heat Back On
Call Thomas Hoffmann Air Conditioning & Heating at (314) 471-7625 for furnace service from a locally owned St. Louis company. If it can wait, you can also send a request through our contact page.
Frequently Asked Questions
Start with the thermostat fan setting. If it is set to On instead of Auto, the blower runs between heating cycles and the air feels cool. A dirty filter or an ignition problem could also be the cause. If the fan setting and filter are fine, call for service.
One reset is generally fine. If the furnace shuts down again, leave it off. Repeated resets may hide a problem the safety controls are trying to flag.
Many newer furnaces use electronic ignition and have no standing pilot. On an older furnace with a pilot, follow the instructions printed on the unit. If you smell gas or the pilot will not stay lit, leave it and call.
A gas smell or a carbon monoxide alarm is always an emergency: leave the house first, then call. No heat during freezing weather is urgent too, especially with young children or older adults at home.